Tyredog TD-4000A-X User Manual

1Precautions ... 3The Main Purpose...

10C. Insert battery with proper direction. D. After battery inserted, the LCD monitor will automatically power on and the display will show graphics a

11E. Close the battery cover onto LCD monitor. 3. The installation of tire pressure sensors As sensor has its own position, you have to make sure it

12Insert batteries in sensors Battery installation for tire pressure sensor A. Take away sensor cap in anti-clockwise direction. B. Insert lithium b

13Take F (front tire) for example NoteΚAfter take away battery, the status of being without battery need to leave for 10 seconds and then insert batte

14Take F.L. (front left) for exampleAnti –theft tool for sensor (optional) Anti –theft tool is designed to prevent the possibility of sensors being ta

15A. Put anti-theft fixed ring onto valve stem. B. Install sensors onto valve stem. Don’t install sensors by brute force. Now, the display will show y

16C. Adjust the anti-theft fixed ring position to install it with sensor in place firmly.D. Put the hex socket screw onto the anti-theft fixed ring. (

17Operation instructions 1. Monitor basic function Locations and function buttons 2. Basic function Power Switch z Press once Power on LCD monitor

18MuteΚon/ off Switch to mute mode. The audible warnings will be disable. When push mute button again, it can go back to both audible and visible warn

19Backlight: on/ off When in darkness, you also can check out tire pressure and temperature by pressing backlight button. The backlight will be off af

2Troubleshooting... 30Additional Information ...

20A. Set pressure measuring unitΚFour types of pressure measuring units: PSI,KPA,BAR and ʦ/ʡ2are provided here. Users can make their own choices by a

21B. Set temperature measuring unit: к and лTwo types of temperature measuring units: к and л are provided here. Users can make their own choices by

22D. Set tire pressure upper warning value The default value is 45 P.S.I. and users can make their own choices by and .E. Set tire temperature upper

23The default value is 70 к and users can make their own choices by and .This mode will return to main screen as long as there is no operation for m

24sensors. As long as enter this mode, insert battery into ‘learnable sensor’ immediately, the LCD monitor will beep once and finish learning process

25Operating procedure 1. InitializationSwitch on LCD monitor to boot up, and LCD monitor will be communicating with sensors and showing tire pressure

263. Automatically power off A. After power on, if there is no signal from sensors in 20 minutes B. Being no signal received for more than one hour

27repeat for 5 times. Take F (front tire) for example C. Tire temperature higher than upper warning value When tire temperature is higher than upper w

28E. Tire pressure sensor runs out of power Battery power in sensor will decrease by daily operation and when power level is lower to some extent, the

29The definition of warnings Item Status Purpose Pattern 1. Power on LCD monitorTo remind rider of power on now Beeps once 2. Tire pressure is

3Precautions 1. For alve stem used on Motorcycle, please use lock-fixed type, not in rubber made. 2. Please make sure the LCD display can receive sign

30warning range, each 1 P.S.I. up, warnings will be given as well. getting high on. Repeat for 5 times. 8. Learnable sensor is integratedFinish l

31D. If these solutions do not help improve the situation, consult your nearest Tyredog dealer. 3. Monitor display color is getting dark. When car

32z Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. z Battery may explode if mistreated. z Do not recharge, d

33User guide 1 piece AAA 1.5V battery 1 piece Product Specifications Tire pressure sensor specifications Frequency 433.92MHz Tire pressure range

411.If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Tyredog dealer. The Ma

5Fuel efficiency is reduced by one percent for every 3 PSI of under inflation. It is for sure that tire pressure is also one of important factors to s

6wireless technology, tire pressure and temperature information is displayed on the friendly Graphic User Interface (LCD monitor). Installationz Do it

7z Sensors are changeable in the very unlikely event of defect or damage, so down time is minimal z Ensure signal accessibility by providing periphera

8Sensor description Graphic User Interface and ContentsSensor battery cover Valve stem connection Monitor status: InitializationNormalConnection Statu

91. System map 2. The installation of LCD monitor Insert batteryΚA. Prepare one AAA-type battery B. Follow the direction A and B on the picture shown