V1.01-FJ04 (1105068) 1INDEX Precautions...3 The Main Purpose...
V1.01-FJ04 (1105068) 10System map Installation The installation of LCD monitor Insert battery: A. Prepare one AAA-type battery.
V1.01-FJ04 (1105068) 111 2 B. Place finger tips near convex bottom edge and open the battery cover. C. Install battery, please follow batter
V1.01-FJ04 (1105068) 12E. Please be careful with the battery cover hook and avoid damage the hooking. F. Please carefully aligned, and press the
V1.01-FJ04 (1105068) 13The installation of tire pressure sensors As sensor has its own position, you have to make sure its defined position. When inse
V1.01-FJ04 (1105068) 14B. Insert lithium battery and make sure battery polarity correct when insert it. Right now, monitor will receive signals
V1.01-FJ04 (1105068) 15C. Fit sensor cap in a clockwise direction. Please refer to “sensor map” to make sure the right position of each sensor an
V1.01-FJ04 (1105068) 16 A. Put anti-theft fixed ring onto valve stem. (Before installed sensor, please make sure the valve stem is prop
V1.01-FJ04 (1105068) 17C. Now, the display will show you the latest valve of tire pressure. D. Adjust the anti-theft fixed ring position t
V1.01-FJ04 (1105068) 18F. When two tire pressure sensors are installed, please check with soap water if the tire pressure sensors and tire valve is c
V1.01-FJ04 (1105068) 19Install monitor to the handle bar bracket Two combinations of a fixed bracket. Method A:This method can directly assemble th
V1.01-FJ04 (1105068) 2Pressure warning value setting...25 Temperature warning value...
V1.01-FJ04 (1105068) 20Remove the original screw from Brake Fluid Reservoir and align bracket, then install the screw back Please use proper force tig
V1.01-FJ04 (1105068) 21Method B Figure: The anti slip pad can be fixed in three sizes 1. Handle bar diameter 1 1/8〞(28mm) 2. Handle bar dia
V1.01-FJ04 (1105068) 22Caution: 1. Recommend not to use other screw for replacement of original screw to prevent damage. 2. Do not over force tighten
V1.01-FJ04 (1105068) 23Monitor basic function Locations and function buttons Basic function Power Switch Press once Power on LCD monitor
V1.01-FJ04 (1105068) 24 Display tire temperature figures Push this button, the LCD monitor will display tire temperature instead of tire pressure.
V1.01-FJ04 (1105068) 25Advanced setting mode Three Seconds Pressure unit setting Temperature unit setting Pressure warning value setting
V1.01-FJ04 (1105068) 26A. Set pressure measuring unit: Four types of pressure measuring units: PSI,KPA,BAR and ㎏/㎝2 are provided here. Users can make
V1.01-FJ04 (1105068) 27C. Setting front wheel lower pressure warning value: Setting front wheel lower pressure warning value, adjust setting with flu
V1.01-FJ04 (1105068) 28E. Set front wheel temperature upper warning value The default value is 70 ℃ and users can make their own choices by “Temperatu
V1.01-FJ04 (1105068) 29G. Setting rear wheel upper pressure warning value Setting rear wheel upper pressure warning value, adjust setting with flush i
V1.01-FJ04 (1105068) 31. Due to rubber valve stem aging under high temperature and expose under the sun, which may cause crack on the rubber stem, th
V1.01-FJ04 (1105068) 30I. Set up monitor time value, adjust setting with flush icon. Press “Temperature button” for adjustment. Note:When
V1.01-FJ04 (1105068) 31Take number 1 for example Five Seconds Sensor learning mode In a very unlike case, sensor could be broken or missed. Sensor l
V1.01-FJ04 (1105068) 32Operation instructions 1. Main screen Switch on LCD monitor to boot up, and LCD monitor will be communicating with sensors and
V1.01-FJ04 (1105068) 333. Abnormal status A. Tire pressure below lower warning value When tire pressure is below lower warning value (default value
V1.01-FJ04 (1105068) 34(default value= 70℃), LCD will appear icon blinks. Push any button, then the LED warnings will be disable.
V1.01-FJ04 (1105068) 35The icon is shown as picture below. Take number 1 for example
V1.01-FJ04 (1105068) 36 The definition of warnings Item Status Purpose Pattern 1. Tire pressure is below lower warning range. The warning of
V1.01-FJ04 (1105068) 37 6. When ire temperature is higher than upper warning range, each 1 PSI up, warnings will be given as w
V1.01-FJ04 (1105068) 38The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist belo
V1.01-FJ04 (1105068) 394. When temperature is below -20 , the response time℃ of CD monitor could be slower. 5. ‘Learning mode’ can only accept ‘lea
V1.01-FJ04 (1105068) 410. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest
V1.01-FJ04 (1105068) 40Under normal conditions, sensor batteries will last approximately 1~2 years. LCD monitor will last around 6 months. (The servic
V1.01-FJ04 (1105068) 41Here are items in whole package. Item Photo number TD4100A-X LCD monitor 1 pieces Ball shape turning fastener 1 p
V1.01-FJ04 (1105068) 421 1/8〞Handle bar anti slip gasket 1 pair 7/8〞Handle bar anti slip gasket 1 pair 1〞Handle bar anti slip gasket
V1.01-FJ04 (1105068) 43TD4100A-X tire pressure sensor 2 pieces CR1632 battery 2 pieces Spanner 1 piece Anti-theft fixed ring 2 pieces Anti-th
V1.01-FJ04 (1105068) 44 Product Specifications Tire pressure sensor specifications Frequency 433.92MHz Tire pressure range 0 ~ 60PSI Accuracy
V1.01-FJ04 (1105068) 5 Reduces fuel expense Fuel efficiency is reduced by one percent for every 3 PSI of under inflation. It is for sure that tire p
V1.01-FJ04 (1105068) 6TYREDOG TPMS (Tire Pressure Monitoring System) - Powerful tool for maximizing uptime and improving safety- The New WTPMS Standar
V1.01-FJ04 (1105068) 7with specially designed electronic sensors. Management Graphic user interface: Powerful graphical user interface for rapid un
V1.01-FJ04 (1105068) 8Monitor description Sensor description Location of controls and
V1.01-FJ04 (1105068) 9 Graphic User Interface and Contents Time Display Connection Status: : Data Received (No icon): Normal
Comments to this Manuals